Benachrichtigungen
Alles löschen
Software
8
Beiträge
4
Benutzer
0
Reactions
7,398
Ansichten
Themenstarter
In order to use the UCCNC software on your STEPCRAFT machine you need the following
- UC100 USB CNC controller
- UC100 license for your UC100 controller
- To download the software from the UCCNC website
- You need to remove the WinPC USB card and install a parallel adaptor card
- You then either need the setup files (please email us) or you need configure step by step using the pin settings in the STEPCRAFT manual
Veröffentlicht : 16/10/2014 12:39 pm
Hallo Rory,
Yesterday arrived my UCCNC-Package.
The installing Guide is very good. After a Short Time it was ready to work
SC 420 + Dremel 4000,Proxxon IBS/E mit JR-Kopf, Vakuumtisch: VT3040 CNC-Plus, Kärcher VC6200, Brushless-JR-Spindel im Aubau 😉
Flugmodellbau und alles was mir in den Sinn kommt 🙂
Veröffentlicht : 17/10/2014 8:43 am
Themenstarter
This is good to hear.
Thank you.
Veröffentlicht : 17/10/2014 1:09 pm
a big Hello Rory from the nord of switzerland
im a cnc prof but new in stepcraft
at the moment i perform a room to be my Stepcraft-paradise :cheer:
The sc 840 is here but she is waiting a few days more for her place to start working ...
there are some reasons to prefere the Uccnc because its closer to fanuc and other prof cnc software then ncpc.
My Questions:
-can you tell me where to get the configuration data for sc 2 840 ?
-are there any problems to think about with the use of sc 840 and uccnc?
-the "tool measure thing" ( :sick: ) is it working ?
beside: i enyoy stoneycnc- videos on youtube with a great pleasure
best reards
Bruno
Veröffentlicht : 01/02/2015 12:55 pm
Themenstarter
there are some reasons to prefere the Uccnc because its closer to fanuc and other prof cnc software then ncpc.
Bruno
Agree - the interface is very clean.
- live view of the machine
- MDI input on screen
- Easy to follow and simple
- 45euro for a licence... we should all very thankful to CNC drive
-can you tell me where to get the configuration data for sc 2 840
Bruno
We have our machine setup and running. Please email us.
-are there any problems to think about with the use of sc 840 and uccnc?
Bruno
We have many STEPCRAFT V1 machines working with UCCNC without problems. The V2 configuration is the same setup with some settings a little different. For example the pitch of the ballscrews is different. So the motor settings for accurate movement in the software are slightly different.
-the "tool measure thing" ( :sick: ) is it working ?
Bruno
Yes the probing function on UCCNC does work. We just need to take some time to confgure it for the STEPCRAFT and make the documentation.
beside: i enyoy stoneycnc- videos on youtube with a great pleasure
Bruno
Thanks!
Veröffentlicht : 01/02/2015 1:53 pm
tx a lot Rory
most of all, i like g54... and mdi
if one does not know it, he does not miss it 🙂
but i miss it badly and im lucky i found it in uccnc
Veröffentlicht : 01/02/2015 8:00 pm
im testing mach3 now for the first time.
There is also g54... and mdi. What a surprise :S
So what is better, Mach3 or uccnc?
Veröffentlicht : 05/02/2015 7:41 pm
Hello Rory,
can I get the UC100, the parallel interface (I bought my stepcraft with a USB Board) and the software bundled and for how much with shipping to Germany?
Veröffentlicht : 03/03/2015 10:47 pm
