Suche
Lieber Nutzer, die Forumssoftware wurde aktualisiert. Für die Erstanmeldung musst Du bitte dein Passwort zurücksetzen.
Dear user, the forum software has been updated. For the first login please reset your password.
Benachrichtigungen
Alles löschen

Celtic Cross

8 Beiträge
4 Benutzer
0 Likes
3,966 Ansichten
Donald McIntosh
(@woodendonkey)
Beiträge: 28
Eminent Member
Themenstarter
 

This was my first piece after building SC600 - not counting the abandoned works while tuning the Stepcraft!

SC600
HF350
1/8" 60deg V-bit
1/8" spiral up-cut
9mm plywood

The up-cut gave it a fuzzy edge that I gave a quick rub with (very rough) sandpaper. Intended as a throwaway piece but my wife took a liking to it and asked me to make a stand to go with it. The stand took me longer to make than the cross - failures of a newbie. 😉

Donald

Donald

Learning from mistakes until I become an expert!

 
Veröffentlicht : 28/12/2014 6:35 pm
Andreas
(@magio2)
Beiträge: 2619
Famed Member
 

Very nice first try! So, we can expect to see some real masterpieces from you once you feel familiar with the steppi :woohoo:

SC 420 mit DIY parallel + Proxxon mit Mod + HF500 + SprintLayout + LibreCAD/QCAD + FreeCAD +WinPC starter/USB->EstlCAM + EstlCAM LPTAdapter + EstlCAM Handrad + DIY Vakuumtisch

Gruß, Andreas

 
Veröffentlicht : 28/12/2014 7:50 pm
(@rory)
Beiträge: 384
Reputable Member
 

Very good demonstration of what Vcarve Can do when coupled to the SC 🙂

Very impressive first efforts. keep up the good work.

 
Veröffentlicht : 28/12/2014 7:58 pm
Donald McIntosh
(@woodendonkey)
Beiträge: 28
Eminent Member
Themenstarter
 

Thanks Andreas - no pressure, eh?

Second project (still on the Celtic theme) - coasters! Two still to cut 🙂

Donald

Learning from mistakes until I become an expert!

 
Veröffentlicht : 28/12/2014 8:05 pm
(@manuelk)
Beiträge: 333
Reputable Member
 

nice one =)

what tool did you use for your vcarv path ?

Gruß,
Manuel

Beruf: Programmierer C, C++, C#, Delphi Pascal für Embedded Systeme (8051, PIC, AVR, AVR32, ARM) sowie PC Applikationen.

 
Veröffentlicht : 28/12/2014 8:17 pm
Donald McIntosh
(@woodendonkey)
Beiträge: 28
Eminent Member
Themenstarter
 

90degree 6.4mm (Dremel bit no. 640)

Donald

Learning from mistakes until I become an expert!

 
Veröffentlicht : 28/12/2014 10:09 pm
(@manuelk)
Beiträge: 333
Reputable Member
 

ah damn sry ^^
i meant with which software

Gruß,
Manuel

Beruf: Programmierer C, C++, C#, Delphi Pascal für Embedded Systeme (8051, PIC, AVR, AVR32, ARM) sowie PC Applikationen.

 
Veröffentlicht : 28/12/2014 10:17 pm
Donald McIntosh
(@woodendonkey)
Beiträge: 28
Eminent Member
Themenstarter
 

VCarve Pro from vectric.com

Donald

Learning from mistakes until I become an expert!

 
Veröffentlicht : 28/12/2014 11:21 pm
Teilen: