Stepcraft 840 winpc...
 
Notifications
Clear all

Stepcraft 840 winpc starter problem!

12 Posts
4 Users
0 Reactions
4,797 Views
simos
(@jeyb)
Posts: 53
Trusted Member
Topic starter
 

hi, i just receive my stepcraft 840 usb , its ready to run with the winpc starter all works perferct but when i cut cycles the are not cycles see pictures , when i cut anything else exept cycle they cut perfect, did anyone know what is the problem?i use corel then estlcam then win pc like i does with my old stepcraft600 lpt for this i have the winpc economy, thanks!

 
Posted : 27/06/2015 4:38 pm
simos
(@jeyb)
Posts: 53
Trusted Member
Topic starter
 

And the three cycles are cut the same , if i loose steps there are will not be the same right? I think is something with the speeds of x y z and the winpc starter they will not have the option for change speeds like economy.

 
Posted : 27/06/2015 5:23 pm
Helmut Brunn
(@mogul)
Posts: 791
Prominent Member
 

Hello jeyb,
it looks as if something had loosened from the mechanics. The deviations are too large for the Backlash

Greeting
Helmut

 
Posted : 27/06/2015 5:41 pm
simos
(@jeyb)
Posts: 53
Trusted Member
Topic starter
 

I checked everything , all screws are tightened in position .

 
Posted : 27/06/2015 6:38 pm
(@bvs)
Posts: 1139
Noble Member
 

Try to shake work spindle axis manualy in all 3 dimensions.
I had a similar Problem after a 7 hour yob. 🙂

 
Posted : 27/06/2015 7:38 pm
simos
(@jeyb)
Posts: 53
Trusted Member
Topic starter
 

Bvs you mean with my hand to move y x z up and down?do you think that something have stuck? But it is quet strange that it make it only in cycles, when i cut cubes there are perfect.

 
Posted : 27/06/2015 7:46 pm
Andreas
(@magio2)
Posts: 2619
Famed Member
 

In squares you only move one axis at a time. You have the same problem, but you don't see it. A square will have deviations of say 2/10mm from the planned measurements. Try it.

If you fix the problem you will have exact results with any shape.

SC 420 mit DIY parallel + Proxxon mit Mod + HF500 + SprintLayout + LibreCAD/QCAD + FreeCAD +WinPC starter/USB->EstlCAM + EstlCAM LPTAdapter + EstlCAM Handrad + DIY Vakuumtisch

Gruß, Andreas

 
Posted : 27/06/2015 8:53 pm
simos
(@jeyb)
Posts: 53
Trusted Member
Topic starter
 

I must turn by hand the motor z y x photo 1 or from the the photo 2?

 
Posted : 27/06/2015 9:39 pm
(@bvs)
Posts: 1139
Noble Member
 

Try to shake work spindle axis manualy in all 3 dimensions. 🙂

Work spindle = where you put your tools in.
When you shake and push and pull here you might find out where you have a unstable part in your cnc.

there must be a unstable part... find it!

Another problem could be Inbusscrews between steper and corresponding spindle not tightend.

search and you will find B)

 
Posted : 27/06/2015 10:42 pm
simos
(@jeyb)
Posts: 53
Trusted Member
Topic starter
 

Ok thanks i will give a try

 
Posted : 27/06/2015 10:56 pm
simos
(@jeyb)
Posts: 53
Trusted Member
Topic starter
 

Can i ask and something else, i use one lap top old with usb1 and windows xp , is there a case that the stepcraft cable is usb2 and i loose data in the transfer from the lap top to stepcraft and that effect the cutting? Is and that one posibility?

 
Posted : 28/06/2015 1:07 am
simos
(@jeyb)
Posts: 53
Trusted Member
Topic starter
 

Ok i find it the in y motor the screw was not tight enought , and now all is perfect

 
Posted : 28/06/2015 10:06 pm
Share: