file Frage software or mechanical fault ! ?

Mehr
28 Feb 2016 20:38 #31377 von Woodsmith
software or mechanical fault ! ? wurde erstellt von Woodsmith
Im totally new to cnc. I expect the odd problem .....but this has me totally stumped.
The attached picture shows two attempts at simple engraving 2mm deep in .5mm steps.
There was no change to the programe or the tool path ...just a different cutter.
First attempt disaster ...second no problem. Dont see where the fault can be !
Please help

Dieser Beitrag enthält einen Bildanhang.
Bitte anmelden (oder registrieren) um ihn zu sehen.

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

  • MagIO2
  • MagIO2s Avatar
  • Offline
  • Forum Nutzer
  • Forum Nutzer
  • Zu viele Ideen und zu wenig Zeit
Mehr
28 Feb 2016 20:49 #31380 von MagIO2
MagIO2 antwortete auf software or mechanical fault ! ?
Would be helpfull to know more about the order in which the things happened in the first try. Did you have a rough milling run (where everything was fine) and then another run for the edges?

Is it the same wood in both cases?

Lookes like the first try was done with a V-grave-endmill and the second try with a normal endmill?!

Which parameters did you use?

You have to understand that a V-grave has a very tiny tip. The tinier the endmill the more RPM you need and/or you have to have smaller feed rates.

SC 420 mit DIY parallel + Proxxon mit Mod + HF500 + SprintLayout + LibreCAD/QCAD + FreeCAD +WinPC starter/USB->EstlCAM + EstlCAM LPTAdapter + EstlCAM Handrad + DIY Vakuumtisch

Gruß, Andreas

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
29 Feb 2016 16:18 #31408 von Woodsmith
Woodsmith antwortete auf software or mechanical fault ! ?
thanks Magl02
piece with fault done first with 20mm 90degree v router cutter
changed to 2mm end mill but changed nothing else in program or tool path
which resulted in plywood engrave success ! All done with just one tool
path

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
29 Feb 2016 18:16 #31422 von Joules
Joules antwortete auf software or mechanical fault ! ?
Does your V cutter have much runout ? lots of vibration when running ?

High Z S1000 router (out of action)
CamBam
Linuxcnc to be replaced by UCCNC + UC-100
OSX Rhino 3D

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
29 Feb 2016 20:12 #31440 von Woodsmith
Woodsmith antwortete auf software or mechanical fault ! ?
no excessive vibration....this fault also happened with end mill cutter at 1mm deep in .5 steps
first letter went wrong next 9 okay moved to next line of text and started jumping again .
these jumps are always in the Y axis .

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Powered by Kunena Forum

© 2022 STEPCRAFT GmbH & Co. KG

Wir benutzen Cookies

Wir nutzen Cookies auf unserer Website. Einige von ihnen sind essenziell für den Betrieb der Seite, während andere uns helfen, diese Website und die Nutzererfahrung zu verbessern (Tracking Cookies). Sie können selbst entscheiden, ob Sie die Cookies zulassen möchten. Bitte beachten Sie, dass bei einer Ablehnung womöglich nicht mehr alle Funktionalitäten der Seite zur Verfügung stehen.