file Frage Adjusting X axis

Mehr
04 Jun 2017 09:01 #47849 von AlanUK
Adjusting X axis wurde erstellt von AlanUK
StoneyCNC have just added this video to their Youtube page, showing adjusting the X axis


SC600/2, Kress 1050, UCCNC with UC100, Cut2D Pro, TurboCAD and Fusion 360
Folgende Benutzer bedankten sich: peterg1000, DocBrown, Doug, SFDeeJay

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
04 Jun 2017 13:01 #47861 von peterg1000
peterg1000 antwortete auf Adjusting X axis
I notice that only the easy two screws are replaced on the stepper - the other two are really awkward b*********s!! :angry:

SC 420/2, Industrial VFD spindle from StoneyCNC
UC100 + UCCNC
Cut2D, Autosketch10, Draftsight, Eagle 9.5.1


There is no problem, however simple, that cannot be made more complicated by thinking about it.

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
05 Jun 2017 14:25 #47910 von Rory
Rory antwortete auf Adjusting X axis
:) fine for demo and test - not essential to verify motion.
once happy two inner fellas can be tightened with care.

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
16 Jul 2017 19:40 #48808 von Radford
Radford antwortete auf Adjusting X axis
I am having a major issue with my X axis. I was cutting a simple profile of a bit of text (1/2"(15mm) MDF with a 1/4"(6mm) 2 flute upcut bit, 16000rpms, 1/8"(3mm) depth of cut passes, 60IPM(25mm per sec)) and the X axis rollers suddenly loosened quite a bit.
I followed Rory's excellent video suggestions for tuning my X axis, then ran another file. When the file was almost finished the X axis rollers again catastrophically loosened.
Does anyone have an idea of how I might resolve this issue?
Any assistance will be greatly appreciated.

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
20 Jul 2017 09:31 #48893 von Rory
Rory antwortete auf Adjusting X axis
IF rollers are loosening then use loctite threadlocker on them

have not come across this before. If you use loctite then super careful if you ever dissasseble as you need more force to remove bolts.

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
20 Jul 2017 11:23 #48898 von MMorao
MMorao antwortete auf Adjusting X axis
Before the Loctite (wot? no duct tape? ) experiment with using lock or spring washers in the fasteners concerned.

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.


Clockwork Orange is a S600 with 4th axis, Kress 1050. Software is UCCNC, DeskProto, Rhino, DraftSight. Also a Silhouette Cameo for vinyl, plastic card, etc.

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
22 Jul 2017 16:02 #48941 von Radford
Radford antwortete auf Adjusting X axis
Thanks Rory, I'm going to get some loctite and give this a try.

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
22 Jul 2017 18:42 #48943 von CNCMiller
CNCMiller antwortete auf Adjusting X axis
make sure you use locktite nr 243 the blue one and not the red variant.

Blue will come lose after some torgue, red will stay fixed.

SC 1/420 + Gantry extension, Kress 1050 FME-P, NeJe 20W Laser, WinPC-NC USB v4.00, Vectric Aspire 9, SolidWorks 2021

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
22 Jul 2017 19:26 #48945 von Radford
Radford antwortete auf Adjusting X axis
Yes, I'm familiar with the different types. Thank you for thinking to post this though, I do appreciate it.

Zeke

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
23 Jul 2017 12:33 #48950 von CNCMiller
CNCMiller antwortete auf Adjusting X axis
Ok,

But as always its better to be safe than sorry :)

good luck

SC 1/420 + Gantry extension, Kress 1050 FME-P, NeJe 20W Laser, WinPC-NC USB v4.00, Vectric Aspire 9, SolidWorks 2021

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
23 Jul 2017 21:08 #48965 von Radford
Radford antwortete auf Adjusting X axis
MMorao, The screws in question are the ones that adjust the tension on the x-axis brass rollers. I think your suggestion would work with many of the other fasteners on the machine, but I couldn't think of anything that is readily available for this particular issue.
Thank you very much for your response.

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
13 Feb 2022 15:10 #62061 von [email protected]
Hi Radfort
I get the same trouble.
Eventually, do you found a solution ?
Regards

manufv

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Powered by Kunena Forum

© 2022 STEPCRAFT GmbH & Co. KG

Wir benutzen Cookies

Wir nutzen Cookies auf unserer Website. Einige von ihnen sind essenziell für den Betrieb der Seite, während andere uns helfen, diese Website und die Nutzererfahrung zu verbessern (Tracking Cookies). Sie können selbst entscheiden, ob Sie die Cookies zulassen möchten. Bitte beachten Sie, dass bei einer Ablehnung womöglich nicht mehr alle Funktionalitäten der Seite zur Verfügung stehen.